The internal API in bluetooth-util should not use the const qualifier
for operations modifying the transport object. This is specially useful
in order to use the available hooks.
If profile could not be successfully initialized, the card should be
set to PROFILE_OFF automatically. If sinks or sources exist, they need
to be destroyed, therefore stop_thread() is called.
Remove stream moving policies from module-bluetooth-device. It is not
clear if such policies are needed at all and in case yes, they should be
implemented in module-bluetooth-policy.
These days we don't set core->default_sink/source as soon as somebody
asks for it. To retain consistent behaviour (i e the asterisk),
we need to call pa_namereg_get_default_sink/source.
Reported-by: Daniel Manrique <daniel.manrique@canonical.com>
Reported-by: Brendan Donegan <brendan.donegan@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
If the card is being set to off profile, it is not necessary to check
if the device exists. This could potentially happen during shutdown,
immediately before the module is unloaded.
It might happen that a PropertyChanged signal is received but the
corresponding card profile has not been created, leading to an assertion
failure in filter_cb() due to inexistent ports. This can happen if BlueZ
misbehaves, or also if the UUIDs are reported later on (i.e. during
pairing discovery). In any case, the signal should just be ignored.
Handling the signal DisconnectRequested should be unnecessary since the
profile-specific interfaces will be later disconnected, leading to
module unload.
Additionally, the signal is problematic: if an interface (i.e.
A2DP AudioSource) is playing at the time DisconnectRequested is
signaled, the following sequence can occur:
1. AudioSource is playing
2. DisconnectRequested is received
3. Module is unloaded due to DisconnectRequested
4. AudioSource state changes from playing to connected
5. module-bluetooth-discover loads the module
6. AudioSource state changes from connected to disconnected
Therefore the module is unnecessarily loaded, to be unloaded immediately
afterwards. This can easily be reproduced if a device is unpaired while
the audio is streaming.
The simplest solution to this consists of removing step 3, by just
ignoring the DisconnectRequested signal. This reverts commit
8169a6a6c9.
Upstreamed from Debian: "Although in principle Ac '97 hardware has a
separate mono LFE pin nothing seems to use it. To make matters worse
it does confuse PulseAudio's port selection slightly which causes
audio in virtualbox not to work out of the box."
Credit: Sjoerd Simons <sjoerd@debian.org>
Credit: Martin-Éric Racine <martin-eric.racine@iki.fi>
BugLink: https://bugs.launchpad.net/bugs/1016969
BugLink: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=673847
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
I was hoping this would improve bootup speed, but it doesn't seem
to do so here, at least not much. But at least it reduces the logs
a little.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
The GNOME-OSTree build system currently creates chroots and bind
mounts to the source tree outside the root; this means that we can't
necessarily run git inside the root, because in the case of git
submodules, the .git repository will point to outside root.
Also, error out fatally if we fail to determine the version; it
makes no sense to put UNKNOWN in e.g. the pkg-config files
since this will just cause errors later on.
Handle availability changes in Bluetooth ports inside
module-bluetooth-policy. The implemented behavior is similar to how
module-switch-on-port-available behaves, but the conditions are more
relaxed and thus more profile changes are triggered.
When PA is doing gateway role, let module-suspend-on-idle resume the
audio stream automatically. This will work until the user (or the remote
side, which we also consider user-initiated) suspend the stream
manually.
Card profile hfgw should be no different from the rest, and thus no
internal policy inside module-bluetooth-device should decide to switch
to its profile automatically.
This should be handled by policy modules.
Handle the Playing->Connected transition gracefully by releasing the
transport and setting the sink and sources as suspended. This is
necessary since the IO thread might not encounter a HUP always.
Until today, setting the card to some profile resulted in a transport
acquisition, leading to audio stream setup. This is generally not very
interesting and even undesireable for HFGW use-cases, where the
Gateway role (the remote end) would typically request the SCO link.
Nevertheless, there is no safe way to implement such check without race
conditions, since the BlueZ's state can change between the state report
and the call to Acquire(). The chances for this to reproduce are quite
low though, since interface state changes are relatively slow.
This race condition requires that BlueZ's API is extended in order to
perform the operation atomically, which has already been discussed and
ack-ed in the BlueZ mailing list.
Note that this patch does not introduce a new race condition, since it
already existed before (the PropertyChanged->Acquire race condition,
affecting HFGW use-cases). It is just more explicit now.
If the acquisition of the transport fails, the profile should still be
set. In this case the audio is not actually streaming, so the sink and
source will be created but left suspended.
If the transport needs to be acquired later, for example because the
user wants to route the audio the remote device, the suspend flag should
have to be changed.
Use the port availability flag to expose whether a certain profile is
connected and whether it's doing actual audio streaming.
The proposed mapping is the following:
- Profile disconnected: port is unavailable
- Profile is connected (but not streaming/playing): availability unknown
- Profile is streaming/playing: port is available
The availability-unknown is specially interesting: it involves that if
the sink/source exists (corresponding card profile set), it is currently
in suspended state.
For example, for SCO cases (HFGW or HSP), this means the SCO is down. A
policy module would typically not change this, unless someone is really
trying to use the sink/source. This situation would be nicely handled by
module-suspend-on-idle, which would automatically connect SCO.
On the other hand, if the user wants to control the status of the SCO,
it will still be possible by resuming the sink or source (suspend=0).
This works out-of-the-box since most UIs would show to the user ports
whose availability is unknown.
The configuration of the transport that depends on the MTU should be
performed every time the transport has been acquired, since the
parameters depend on what the Media API provides. This requires to
update the parameters of the sinks and sources as well.
This patch moves this code into a new function that will be called
when the stream is starting (setup_stream), from the IO thread.
This makes the code more robust, since the existing multiple calls to
bt_transport_acquire() do not rely on setup_bt() being able to acquire
the transport.
There should be one port per sink/source so a dummy set_port callback
will be enough.
Adding this callback avoid the "operation not implemented" error
message and additionally makes the module work nicely with
module-switch-on-port-available.
The transport might have disapeared exactly before acquiring, so we
should avoid an assertion failure, in this case inside the function
pa_bluetooth_discovery_get_by_path().
The HFGW source should be consistent with the sink by not setting the
"phone" intended role.
Even though setting this role seems to make sense strictly speaking, the
rest of the codebase doesn't handle this well. Therefore, the audio
coming from a Bluetooth phone can be routed back to the same device.
Make code more readable by introducing the helper function
bt_transport_is_acquired(). This also adds assertions to check whether
the internal state is consistent.
Previously, sink_input_kill_cb would cleanup u->sink an then unload the
module. However, during module unload, both save_state and dbus_done
tried to use u->sink, causing a segfault or assertion failure.
The segfault is easy to reproduce: Load module-equalizer-sink and then
press ctrl-C to terminate pulseaudio.
This commit removes the u->sink cleanup in sink_input_kill_cb, since
u->sink will be cleaned up by the module's pa__done as well (after it
has been used).
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Nowadays, we are using more hashmaps and other things, than we did
before. Therefore, I often get the "flist is full (don't worry)"
message. This change should avoid that message. I was unable to find
any significance in increase of memory footprint from this change.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Interestingly, the name is properly matched even though there
is no paths/iec958-stereo-input.conf file.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
This check was valid before we introduced per-source-output volumes, so
dropping it now. Thanks to Alban Browaeys <prahal@yahoo.com> for
catching this.
During initialization, the approach avoids having a needless short
period of corked state in case the sink is suspended, by always creating
the source-output corked and uncorking it immediately afterwards when
the sink is not suspended.
During initialization, the approach avoids having a needless short
period of corked state in case the source is suspended, by always
creating the sink-input corked and uncorking it immediately afterwards
when the source is not suspended.
Keeping the SBC check separate means we can keep the SBC_LIBS/CFLAGS
separate, which is cleaner. Thanks to Jan Steffens for pointing out that
this was broken (SBC_* wasn't actually changed to match the configure
change).
This reverts commit da5078e5c7.
