Although the hdmi-output is in well_known_descriptions[] table,
the hdmi device names are indexed (hdmi-output-0), thus there
is no match to assign the proper type automatically.
This patch puts the correct hdmi type to all relevant hdmi
configuration files.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
We have a requirement to "hide" some hardware drivers, because
other (main) UCM configuration will refer them.
This patch use special error codes to notify the upper layers
to skip the module loading.
BugLink: https://github.com/alsa-project/alsa-ucm-conf/issues/30
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
There were three bugs:
1) j->state_plugged was set to PA_AVAILABLE_UNKNOWN too early. It must
be set only after we have found that the jack is shared by two ports.
The result of setting it too early was that no jack ever could have
the PA_AVAILABLE_YES status.
2) The inner jack loop iterated through p->jacks instead of p2->jacks,
so the code didn't compare jacks between two ports at all. As a result
all ports were put in the same availability group.
3) The inner jack loop checked j->state_plugged instead of
j2->state_plugged. The result was that the speaker port, which uses the
Headphone jack to toggle between unknown and unavailable, was put in the
same group with the headphone port.
If the profile is generated from UCM, the priority won't be set so it
stays as 0.
Assume a card has two available profiles, when the selected one becomes
unavailable, module-switch-on-port-available's find_best_profile()
should pick the next available one. However, since the priority is 0,
the "off" profile was chosen instead of the available one.
So let's set the priority to 1 to make profile that is available has
higher priority than "off" profile.
UAC v2 and v3 support insertion control (jack detection), and the
created jack mixers have "- Input" suffix and "- Output" suffix for
input jack and output jack, respectively.
Add these jacks so we don't always need to rely on UCM or PulseAudio
profile-set.
On the machines with the ucm used, the different input/output devices
often have different pcm stream, so they often belong to different
sources and sinks, this is greatly different from the design of all
devices connected to a codec (without ucm).
For example, on a machine with ucm2 used:
the internal dmic is on source#0
the external mic is on the source#1
the internal spk is on sink#0
the external headphone is on sink#1
Users expect that after plugging the external device, it will become
the active device automatically. The switch-on-port-available could
make it to be the active_port on its own source/sink, but can't make
source/sink to be default_source/sink since the sources/sinks belong
to the same profile (HiFi usually).
If we adjust the source/sink priority according to ucm ports priority,
the device_port.c could handle the default_source/sink changing then.
Usually we set higher priority for external device than internal
device in the ucm.
In order to bring the lowest side effect on the source/sink priority,
I change the ucm priority to units digit first, then add it to the
original priority.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
We met a weird situation on a couple of Lenovo machines and at least
on one Dell machine. First we open the gnome-sound-setting, then
suspend and resume the system, after the system resume back, the audio
devices change to dummy, the audio doesn't work anymore. And pacmd
list-cards shows no available sound card.
Through debugging I found after resume, the alsa receives POLLERR
events and it will call unsuspend to recover the pcm, but at that
moment, the device nodes in /dev/snd/ is not accessible, so the
snd_pcm_open() fails and the pulseaudio unload the module-alsa-card.
Here I add retry and pa_msleep if snd_pcm_open fails, I tested it on
all machines which have this problem, pa_msleep(25) is ok for most of
them, there is only one machine which needs to call pa_msleep(25)
twice, so for safety reason, I set the max retry times to 4.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
It's possible for mdev to be NULL. In this case, an assert is taken
in pa_alsa_open_mixer_by_name() with debug builds, and a crash with
release builds. However, it's possible to bypass this trouble by taking
the error path if mdev is NULL.
Reported-by: Jarkko Sankala <jarkko.sankala@offcode.fi>
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Previously avoid_resampling was always false unless the sink or source
implementation explicitly configured the variable. The null sink doesn't
explicitly configure it, so it didn't switch the sample rate as
expected when avoid_resampling was enabled.
This change means that also sinks that don't support rate switching can
have avoid_resampling set to true, but I think that's fine, because
pa_sink_reconfigure() doesn't try to do anything if the reconfigure()
callback isn't set.
Fixes: https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/issues/923
There is some case that multiple ucm devices share an amixer Jack
like "Headphones", "Headset" and "Mic2" share the "Headphone Mic Jack",
When the Jack state is changed, the module-switch-on-port-available
will process them in the order they are in the jack->ucm_devices, and
the last device will decide the final setting.
But usually users put priority for those devices and expect the
final setting is based on the highest priority device if there is no
other policies like manual selection. So here do some change to store
the ucm_devices according to their priority (from low to high).
For example, we have ucm devices definition like below (ucm2):
SectionDevice."Mic2" {
Comment "Headphones Stereo Microphone"
...
Value {
CapturePriority 200
...
}
SectionDevice."Headset" {
Comment "Headset Mono Microphone"
...
Value {
CapturePriority 300
...
}
}
Without this patch, the final setting is based on Mic2, after applying
this patch, the final setting is based on the Headset (with higher
priority than Mic2).
Signed-off-by: Hui Wang <hui.wang@canonical.com>
- remove duplicate mixer initialization in sink
- use the similar mixer initialization for source like for sink
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The UCM device must be activated using the pa_alsa_ucm_set_port()
call on boot (the sink creation time). In case when the
mixer controls are not defined for the application in the
UCM configuration, the mixer_handle is NULL.
Call the pa_alsa_ucm_set_port() before the mixer_handle check.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
It's completely normal to not have explicit channel configuration for
stereo devices. In fact, the ALSA developers actively avoid configuring
the channels for stereo devices.
I also dropped the word "duplex" from the messages, because "stereo
duplex" implies bidirectionality, but most devices use one direction
only.
The ALSA mixer can be opened multiple times (especially for UCM
in the probe). This adds a simple mixer cache to prevent
multiple open calls.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This is just invalid. It results to an error in almost all cases.
The hw:<number> scheme is sufficient to get the right card mixer.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
