Some older cards do not have jack detection. This patch makes the
port still show up.
An implementation detail: the "required = ignore" line has in itself
no effect, but we have to write *something* there, or else the entire
jack detection section will be ignored by the parser.
BugLink: https://bugs.launchpad.net/bugs/961286
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
While developing the new UI we had to ask ourselves the question of whether
"speakers" should be considered available when headphones are plugged in.
In most cases, they are not available and therefore we should list them
as such.
OTOH, we don't want unplugging the headphones to be considered an act of
wanting to use the speakers (the user might prefer HDMI), and there might
be line-outs that keeps the speakers from unmuting anyway. So, at this point,
I think the most reasonable would be to make the speakers have
PA_PORT_AVAILABLE_NO when headphones are plugged in and
PA_PORT_AVAILABLE_UNKNOWN when they are not. But we might want to revisit
this decision once we have the priority lists up and running.
The same reasoning applies for "Internal Mic", which should become unavailable
when any other mic is plugged in.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
For Nvidia and Intel, support probing of up to four HDMI devices.
Also add port information to all HDMI profiles.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Support the new jack detection interface implemented in Linux 3.3
(and Ubuntu's 3.2 kernel).
Jacks are probed and detected using the snd_hctl_* commands, which
means we need to listen to them using fdlists. As this detection
needs to be active even if there is currently no sink for the jack,
so this polling is done on the card level.
Also add configuration support in paths, like this:
[Jack Headphone]
required-any = any
...where 'Jack Headphone' should match 'Headphone Jack' as given by
ALSA (as seen in e g 'amixer controls').
"Required", "required-any" and "required-absent" is supported. Using
required-any, one can have several ports even though there is no
other indication in the mixer that this path exists.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
"Front Speaker", "Surround Speaker" seems to be a common enough name
to make it into alsa-utils, so we should probably care about it as
well. In this case, there was a macbook pro whose speakers didn't work
without these controls.
BugLink: http://bugs.launchpad.net/bugs/551441
Reported-by: Jeroen T. Vermeulen <jtv@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
This is needed for the Creative Audigy CA0106 to work. Also makes sure
that the LED for optical out is shut down in analog modes on MacBooks
(these share a port for analog and digital output).
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=44741
Just like we turn off the "Front Mic" element when we select "Rear Mic",
we should also turn off the "Front Mic Boost" element. And the same for
the other inputs.
Reported-by: Len Owens <len@ovenwerks.net>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
I've seen more than one system where the volume control named
"Front" is a part of audio path for headphones. This is somewhat
of a compromise: While we don't merge it into the path, as that
would be regressing machines where "Front" isn't a part of the
audio path, it would still enable sound on these machines.
BugLink: http://bugs.launchpad.net/bugs/804178
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
The priorities should be set in the approximately likeliness that someone
would like to use them. This is hard to guess of course, but this is
a better guess compared to the existing configuration.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
The "Line HP Swap" element needs to be set correctly for some Dove
boards to work correctly. Thanks to Daniel T Chen for the patch.
BugLink: http://bugs.launchpad.net/bugs/451635
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
This switch needs to be off for analog output to work on several
Audigy cards.
Thanks to Daniel T Chen for the patch.
BugLink: http://bugs.launchpad.net/bugs/408370
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
This change makes it possible to configure an arbitrary constant volume for a
volume element in the path configuration, which is applied when the path is
selected. Note: this is only useful when the exact hardware and driver are
known beforehand.
This feature is mainly useful in embedded systems that have built-in speakers.
In such situations the full audio path is known beforehand, so it's possible to
know what is the maximum sensible volume, and any higher volume can be
disabled.
The volume limit is set in path configuration files in the [Element] section,
using option "volume-limit". The value is the desired maximum volume step of
the volume element.
Make sure that mic and line (with common names) use the specific
path instead of the analog-input one.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Now you can add required-any to elements in a path and the path
will be valid as long as at least one of the elements are present.
Also you can have required, required-any and required-absent in
element options, causing a path to be unsupported if an option is
(not) present (simplified example: to skip line in path if
"Capture source" doesn't have a "Line In" option).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
This is needed to better support out of tree builds (including
distcheck) and to ensure the necessary folders are created in the
build tree on configure and also works around an intl-tools bug
(https://bugs.launchpad.net/intltool/+bug/605826)
The Makefile.am's used are minimal (and in some cases completely
blank). At present they do not include anything interesting
with the majority of the real work still done by the monolitic
src/Makefile.am
It may make sense to start splitting out src/Makefile.am into
smaller chunks but this commit makes the minimum changes to address
the issues that result from using make distcheck and other out of
tree builds.
Note: This 'breaks' the ability to type make in e.g. the src/modules
folder and have all of PA rebuilt accordingly (this is because the
static Makefiles previously present just did a "make -C ..") which
was purportedly for use in emacs. But I'm sure there will be a better
and more robust way to configure emacs to do your builds properly if
this behaviour is still desirable.
BugLink: https://launchpad.net/bugs/680810
Some laptops have 'Internal Mic 1' exposed as an 'Input Source', e.g., Dell
XPSM 1530, so handle these, too.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
This is not 100% ideal as we have not way to tie specific boosts to specific
inputs and this particular chipset (as noted in #772) appears to
support just that.
For the time being incorporate it into the normal boost logic.
See http://pulseaudio.org/ticket/772
Completely rework mixer logic. This now allows controlling a full set of
elements from a single sink's volume slider/mute button.
This also introduces sink and source "ports" that can be used to choose
different input or output ports with the UI. (i.e. "mic"/"line-in" or
"speaker"/"headphones".
The mixer paths and device maps are now configered in external
configuration files and can be tweaked as necessary.
