Issue: When HFP/HSP profile is used with certain BT chipsets, the
audio sounds heavily distorted, with very slow playback full of noise.
During recording, the samples are dropped and it distorts the recorded
audio samples.
The root cause of both the issues are related to the fixed MTU sizes
in the PA stack, which is 48 bytes. Here, the BT chipset CC256x had
180 bytes MTU and it was being under-utilized and the rate at which
the samples were being accepted where not matching the expected rate,
and hence the distortion.
Solution: The appropriate solution to this problem is by reading the
MTU size of the SCO socket using getsockopts dynamically.
BugLink: http://bit.ly/2gDpGPv
BugLink: http://bit.ly/2hQsARK
FSF addresses used in PA sources are no longer valid and rpmlint
generates numerous warnings during packaging because of this.
This patch changes all FSF addresses to FSF web page according to
the GPL how-to: https://www.gnu.org/licenses/gpl-howto.en.html
Done automatically by sed-ing through sources.
Send the right command to set the speaker and microphone gain.
Note that setting the volume on the Headset should use the unsolicited
result code. Receiving the volume from the Headset uses the AT
command.
supresses a warning when compiling with NDEBUG:
pulsecore/aupdate.c: In function 'pa_aupdate_read_end':
pulsecore/aupdate.c:82:14: warning: variable 'n' set but not used [-Wunused-but-set-variable]
unsigned n;
pulsecore/sink-input.c: In function 'pa_sink_input_unlink':
pulsecore/sink-input.c:648:27: warning: variable 'p' set but not used [-Wunused-but-set-variable]
pa_source_output *o, *p = NULL;
pulsecore/sink-input.c: In function 'find_filter_sink_input':
pulsecore/sink-input.c:1523:14: warning: unused variable 'i' [-Wunused-variable]
unsigned i = 0;
pulsecore/sink-input.c: In function 'pa_sink_input_start_move':
pulsecore/sink-input.c:1569:27: warning: variable 'p' set but not used [-Wunused-but-set-variable]
pa_source_output *o, *p = NULL;
CC pulsecore/libpulsecore_5.0_la-sink.lo
pulsecore/sink.c: In function 'pa_sink_unlink':
pulsecore/sink.c:673:24: warning: variable 'j' set but not used [-Wunused-but-set-variable]
pa_sink_input *i, *j = NULL;
pulsecore/source-output.c: In function 'find_filter_source_output':
pulsecore/source-output.c:1179:9: warning: unused variable 'i' [-Wunused-variable]
int i = 0;
CC pulsecore/libpulsecore_5.0_la-source.lo
pulsecore/source.c: In function 'pa_source_unlink':
pulsecore/source.c:616:27: warning: variable 'j' set but not used [-Wunused-but-set-variable]
pa_source_output *o, *j = NULL;
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Enable both ofono and native backends to be built into the same
libbluez5-util. Never build the null backend.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
We weren't writing out one character from the "OK" response, and the
"AT" part of the "+VGS" and "+VGM" commands was missing. Also, the spec
says that the command is terminated by only a CR and not an LF (probably
doesn't hurt, but let's adhere to the spec for now).
Parse the gain changed AT commands from the headset and fire 2 new
hooks as a result. The device will connect to those hooks and change the
source/sink volumes.
When the source/sink volume changes, set the gain on the microphone or
speaker respectively. Make sure we do nothing if the transport can not
handle the gain changes.
Add a simple native headset backend that implements support for the
blutooth HSP profile.
This allows pulseaudio to output audio to a Headset using the HSP profile.
Make the native backend the default.
