create_card_profile() used to get called separately for HSP and HFP,
so if a headset supports both profiles, a profile named
"headset_head_unit" would get created twice. The second instance would
get immediately freed, so that wasn't a particularly serious problem.
However, I think it makes more sense to create the profile only once.
This patch makes things so that before a profile is created, we check
what name that profile would have, and if a profile with that name
already exists, we don't create the profile.
A couple of Yocto releases (jethro and krogoth) have non-upstream
patches that suffer from this double creation. The patches add
associations between profiles and ports, and those associations use
the profile name as the key. When the second profile gets freed, the
associations between the profile and its ports get removed, and since
the profile name is used as the key, this erroneously affects the
first profile too. Crashing ensues.
BugLink: https://bugzilla.yoctoproject.org/show_bug.cgi?id=10018
I want module-alsa-card to set the availability of unavailable
profiles before the initial card profile gets selected, so that the
selection logic can use correct availability information.
module-alsa-card initializes the jack state after calling
pa_card_new(), however, and the profile selection happens in
pa_card_new(). This patch solves that by moving parts of pa_card_new()
to pa_card_choose_initial_profile() and pa_card_put().
pa_card_choose_initial_profile() applies the profile selection policy,
so module-alsa-card can first call pa_card_new(), then initialize the
jack state, and then call pa_card_choose_initial_profile(). After that
module-alsa-card can still override the profile selection policy, in
case module-alsa-card was loaded with the "profile" argument. Finally,
pa_card_put() finalizes the card creation.
An alternative solution would have been to move the jack
initialization to happen before pa_card_new() and use pa_card_new_data
instead of pa_card in the jack initialization code, but I disliked
that idea (I want to get rid of the "new data" pattern eventually).
The order in which the initial profile policy is applied is reversed
in this patch. Previously the first one to set it won, now the last
one to set it wins. I think this is better, because if you have N
parties that want to set the profile, we avoid checking N times
whether someone else has already set the profile.
pa_module_unload() takes two pointers: pa_module and pa_core.
The pa_core pointer is also available via the pa_module object,
so the pa_core argument is redundant
[David Henningsson: Rebased to git HEAD]
Flushing the asyncmsgq can cause arbitrarily callbacks to run, potentially
causing recursion into pa_thread_mq_done again. Because of this; rtpoll which
is cleared in the second iteration is tried to free once again by the first
iteration leading to PA crash.
FSF addresses used in PA sources are no longer valid and rpmlint
generates numerous warnings during packaging because of this.
This patch changes all FSF addresses to FSF web page according to
the GPL how-to: https://www.gnu.org/licenses/gpl-howto.en.html
Done automatically by sed-ing through sources.
In case a transport is currently disconnected and transitions to
idle, that should not count as a "remote hang up" event.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Parse the gain changed AT commands from the headset and fire 2 new
hooks as a result. The device will connect to those hooks and change the
source/sink volumes.
When the source/sink volume changes, set the gain on the microphone or
speaker respectively. Make sure we do nothing if the transport can not
handle the gain changes.
If the transport for the profile doesn't exist, the old behaviour was
to leave cp->available at the default value, which is
PA_AVAILABLE_UNKNOWN, but if there's no transport, the profile should
be marked as unavailable.
This commit adds basic support for devices implementing HSP Headset
Unit, HSP Audio Gateway, HFP Handsfree Unit, HFP Audio Gateway to the
BlueZ 5 bluetooth audio devices driver module (module-bluez5-device).
The code in the "io_fail" section was only used for HUP handling, but
there were jumps to there also from places where reading or writing
failed, because the read/write failure could have been caused by HUP.
This patch simplifies things by checking for HUP condition before
trying to read or write. Now if reading or writing fails, we will
jump to "fail" directly instead of going via the "io_fail" label. As
a result, the "io_fail" label isn't needed any more.
This name is more acurate with regards of what role we're currently
playing and we've already been using it in
pa_bluetooth_profile_to_string() since 449d6cb.
Currently the latency information is being updated based on the encoded
SBC data instead of the decoded PCM data. Fixing this required moving
the timing update to be after the packet has been decoded.
The Nokia E7 running Symbian Belle Refresh seems to generate invalid SBC
packets every few minutes. This causes pulseaudio to disconnect the
stream and log "SBC decoding error (-3)".
If a single packet is bad, pulseaudio should keep playing the stream.
When setting attribute foo, or in this case the card profile, in my
opinion the thing passed to the set_foo() function should be of the
type of foo, not a string identifier that can be used to search for
the actual foo in set_foo().
This is mostly a question of taste, but there's at least some small
benefit from passing the actual object: often the profile object is
already available when calling pa_card_set_profile(), so passing the
card name would cause unnecessary searching when pa_card_set_profile()
needs to look up the profile from the hashmap.
For quite some time now the device driver module doesn't work well
without the discovery module, so for the BlueZ 5 support we'll prevent
the device driver module to be loaded if the discovery module is not
loaded.
Create the thread function, the render and push functions for A2DP, the
process message function for communication between the I/O thread and
the main thread, and other helper functions related to them.
Get the remote device information stored in pa_bluetooth_discovery. This
also creates the mandatory parameter 'path' for module-bluez5-device,
which is used to inform the object path of the remote device in BlueZ on
the module load.
