When this headset works in HFP/HSP profile, the input/output volume
adjustment doesn't work if the headset is playing sth or capturing
sth. Through the btmon log, we could see "+VGS" and "+VGM" were sent
to headset and headset replied "command success", but the volume was
not changed.
It is something like once the SCO connecton is built, the volume
couldn't be changed by "+VGS" and "+VGM" commands. Here add a quirk
for this headset, skip to set set_sink_volume and set_source_volume,
after this change, the pulseaudio will apply the software volume
adjustment to this headset in the HFP/HSP mode. This change doesn't
impact A2DP volume adjustment for this headset.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
My log files get completely clobbered by this; thousands of lines of:
Jan 18 18:14:44 pulseaudio[29946]: [pulseaudio] backend-native.c: Dock Status: undocked
Jan 18 18:15:39 pulseaudio[29946]: [pulseaudio] backend-native.c: Battery Level: 50%
Jan 18 18:15:39 pulseaudio[29946]: [pulseaudio] backend-native.c: Dock Status: undocked
Jan 18 18:16:34 pulseaudio[29946]: [pulseaudio] backend-native.c: Battery Level: 50%
Jan 18 18:16:34 pulseaudio[29946]: [pulseaudio] backend-native.c: Dock Status: undocked
Jan 18 18:17:29 pulseaudio[29946]: [pulseaudio] backend-native.c: Battery Level: 50%
Jan 18 18:17:29 pulseaudio[29946]: [pulseaudio] backend-native.c: Dock Status: undocked
Jan 18 18:18:25 pulseaudio[29946]: [pulseaudio] backend-native.c: Battery Level: 50%
Jan 18 18:18:25 pulseaudio[29946]: [pulseaudio] backend-native.c: Dock Status: undocked
Jan 18 18:19:20 pulseaudio[29946]: [pulseaudio] backend-native.c: Battery Level: 50%
Jan 18 18:19:20 pulseaudio[29946]: [pulseaudio] backend-native.c: Dock Status: undocked
Jan 18 18:20:15 pulseaudio[29946]: [pulseaudio] backend-native.c: Battery Level: 50%
This seems like it should be a debug log, not a notice.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/810>
When we connect Lenovo XT99 bt headset in the Ubuntu 22.04, this
headset could only work in A2DP profile, couldn't work in HFP profile
with a high chance.
This headset supports mSBC, after pulseaudio replies "+BCS:2" to
headset, we expect to receive a "AT+BCS=2\r" from the headset, but
with a high chance, it will receive 2 AT commands in a buffer like
this "AT+CHLD=?\rAT+BCS=2\r", and we also observed other 2 AT commands
in a buffer like this "AT+NREC=0\rAT+CGMI?\r".
Here we don't suppose there is only one AT command in a buffer, we
will find each command by the delimiter "\r" and handle each command
by sequence.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/804>
Incoming RFCOMM string has extra end-of-command terminating character which
breaks both AT+BIA= and AT+BAC= parsers which only expect a comma.
This leads to error parsing last element of response in both cases and could
prevent detecting mSBC availability if mSBC codec id comes last, e.g. AT+BIA=1,2
Fix this by additionally checking for delimiters in both parsers.
Fixes: 3c63f8e6d ("backend-native: Fix stack corruption reading RFCOMM AT+BIA= response")
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/768>
When `indicator` is initialized to `1`:
- it always succeeds the `indicator == CIND_CALL_INDICATOR` check;
- hence always calls `continue`;
- hence never reaches the end of the `while` loop where `indicator++` is
called;
- hence `indicator` never contains any other value than `1` meaning
`cind_enabled_indicators` is ever updated.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/740>
This removes the inverse/recursive dependency of backend-native on the
`pa_bluetooth_discovery` struct, which is supposed to be opaque outside
of `bluez5-util` in favour of the many accessor functions defined in
`bluez5-util.h`.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/740>
AT+BIA is used to enable/disable CIND indicators by Bluetooth HFP spec.
By default, all indicators are enabled on connection.
AT+BIA will configure which indicators should be disabled then,
the disabled indicators may be enabled later on again with AT+BIA.
When the connection is lost and recovered, all indicators are enabled
again. The HF will reconfigure the indicators again with an AT+BIA
command.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/631>
Commit 7fd89e491 ("bluetooth: Try to reconnect SCO") introduces a call
to pa_msleep but failed to include the header, resulting in a:
../pulseaudio/src/modules/bluetooth/backend-native.c: In function ‘sco_acquire_cb’:
../pulseaudio/src/modules/bluetooth/backend-native.c:336:17: warning: implicit declaration of function ‘pa_msleep’ [-Wimplicit-function-declaration]
336 | pa_msleep(300);
| ^~~~~~~~~
(Un)fortunately this implicit declaration gets resolved at link-time,
otherwise the issue would have been caught sooner.
Fixes: 7fd89e491 ("bluetooth: Try to reconnect SCO")
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/651>
When the SCO connection is in use, if you disconnect first and then connect,
the SCO connection will occasionally fail, and the Bluetooth error code is 42
(0x2A in hexadecimal). This is usually because an error occurred when the SCO
connection was initiated, we need to try to reconnect to optimize the handling
of this problem. The log returned by the kernel is as follows:
Bluetooth: sco_connect_cfm: hcon 0000000003328902 bdaddr 40:ef:4c:0c:11:f0 status 42
Bluetooth: sco_sock_connect status is -38
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/622>
With USB Alternate Setting 3 size of HCI payload is 72 bytes which is already
larger than mSBC frame size. Largest known size of HCI payload is with USB
Alternate Setting 5 (144 bytes), make it the default SCO socket MTU.
Reserve additional space in bluetooth encoder buffer to cover this case.
Since mSBC encoder and decoder will now work with larger packet sizes, drop
assertions about MTU larger than mSBC frame size.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/617>
Try to register profile support again after RegisterProfile fails, when
BlueZ indicates no one else is implementing the profiles we are
interested in.
Ideally this would rely on a list of UUIDs supported by the profile
manager instead of the adapter, but BlueZ has no such API.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/593>
HF indicator 2 (see [assigned-numbers], Hands-Free Profile) is able to
report battery percentage at 1% intervals (in range [0, 100]), contrary
to the `+XAPL` `+IPHONEACCEV` extension which only supports 10%
increments. This does not guarantee increased granularity however, as
peers may still be limited to imprecise battery measurements internally
or round to coarser percentages.
Supporting both additionally broadens the range of devices for which PA
can report its battery level.
[assigned-numbers]: https://www.bluetooth.com/specifications/assigned-numbers/
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/482>
Whenever a device disconnects the device is not removed from BlueZ, only
the profiles that had an active connection are disconnected. Since we
were providing this battery level based on AT commands received through
HSP/HFP these services should be responsible for deregistering it again.
Deregister the interface to signal BlueZ (And UPower in return) that the
battery level won't be accurate/updated anymore.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/482>
The peer will wait some time and eventually time out the connection if
no reply is sent back. When sending `ERROR` the peer can decide to break
the RFCOMM connection immediately or continue when a command is not
critical.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/482>
Devices for Apple's iOS uses a few extra HFP AT commands to
inform the iPhone about the headphone's battery status.
Apple documented the AT commands in the following document:
https://developer.apple.com/hardwaredrivers/BluetoothDesignGuidelines.pdf
The patch has been tested with a Bose QC35, which results
in the following communication:
D: [pulseaudio] backend-native.c: RFCOMM << AT+VGS=14
D: [pulseaudio] backend-native.c: RFCOMM >> OK
D: [pulseaudio] backend-native.c: RFCOMM << AT+XAPL=009E-400C-0129,3
D: [pulseaudio] backend-native.c: RFCOMM >> +XAPL=iPhone,2
D: [pulseaudio] backend-native.c: RFCOMM >> OK
D: [pulseaudio] backend-native.c: RFCOMM << AT+XEVENT=Bose SoundLink,158
D: [pulseaudio] backend-native.c: RFCOMM >> OK
D: [pulseaudio] backend-native.c: RFCOMM << AT+IPHONEACCEV=2,1,4,2,0
N: [pulseaudio] backend-native.c: Battery Level: 50%
N: [pulseaudio] backend-native.c: Dock Status: undocked
D: [pulseaudio] backend-native.c: RFCOMM >> OK
[Marijn: Adapt for recent HSP/HFP code changes]
Co-authored-by: Marijn Suijten <marijns95@gmail.com>
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/482>
A few headsets have issues if HFP HF profile connection is attempted before
HSP HS profile connection is closed. Looks like this could happen because
bluez bluetoothd alows to make simultaneous HSP HS and HFP HF peer connections.
One of affected headsets is WH-1000XM2
Until we find out how to prevent simultaneous HSP HS and HFP HF connections,
when native backend has HFP HF profile enabled (this is the default) do disable
HSP HS completely unless user explicitly request it via discovery modarg.
Do this by adding module-bluetooth-discover arg enable_native_hsp_hs,
default to inverse of enable_native_hfp_hf.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/538>
For mSBC to work correctly the following must be set correctly
- codec object
- transport write method
- transport setsockopt method
Use helper method to set all three simultaneously.
Static configuration structure may be cleaner solution.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/507>
HFP Audio Connection SCO configuration is negotiated symmetrically in both
directions, and USB HCI SCO packet framing is also symmetric in both directions.
This means that packet size will be the same for reads and writes over HFP SCO
socket.
HFP profile specification states that valid speech data shall exist on the
Synchronous Connection in both directions after the Audio Connection is
established.
This guarantees that an incoming packet will arrive shortly after SCO connection
is established. Use it's size to fix write MTU in case kernel value is wrong.
Discussion here https://lore.kernel.org/patchwork/patch/1303411/
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/507>
The HFP protocol supports the ability to negotiate codecs if that is
supported by both AG and HF. This patch adds advertising of codec
negotiation support and the ability to negotiate a codec change. The
only currently supported extra codec (as of HF 1.7.1) is mSBC. mSBC
requires that the transmission be done over an eSCO link with
Transparent Data. The linux kernel ensures the former, but we have to
manually set the socket to transparent data.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/507>
Bluez prepends newly registered profile to a list of supported profiles,
and new peer profile connections are attempted in reverse order of profile
registration.
Currently native backend would register HFP AG profile before HSP AG profile.
When peer supports both HFP HF and HSP HS profiles, this registration order
causes extra HSP HS connection attempt before native backend would reject it
to make sure peer is reconnected with HFP HF profile.
Reorder HSP AG profile registration before HFP AG to make sure peer supporting
both profiles connects with HFP HF profile first.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/534>
HF/HS hardware attenuation is optional on HFP: the peer indicates
support with the AT+BRSF command, when bit 4 is set. That does not
explicitly mandate speaker or microphone gain control; either is
dynamically detected as soon as `AT+VG[MS]=` is received. Otherwise
software attenuation is performed.
It is also optional on HSP but nothing is mentioned about feature
detection, assume it is the same as HFP: perform software attenuation
until the HF/HS peer sends an `AT+VG[MS]=` command.
When PA is a HS/HF (and the peer the AG) we attenuate both channels in
software and unconditionally keep the peer up to date with
`AT+VGM/AT+VGS` commands.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/521>
Generalize the distinction between local and peer-attenuated volumes
into a function, paving the way for future changes where this needs to
be checked in more places and when A2DP Absolute Volume support is
added.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/521>
Sink and source naming is more generic when dealing with audio that is
directional in the sense that it either goes to or comes from the other
device, but not necessarily a microphone or speaker. A concrete example
is the swapped meaning when the current device is in the HeadSet
profile. The incoming audio can come from any source, not necessarily a
microphone. Likewise, audio captured by the microphone of the headset is
not necessarily played back by a speaker on the AG, it is merely acting
as a sink for the data: further handling is irrelevant to the naming.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/521>
For the upcoming A2DP AVRCP Absolute Volume feature the code in BlueZ5
has to be generic to be reusable. Move this conversion so that it
becomes possible to implement A2DP volume - which uses different values
- on top without duplicating existing callback functionality.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/521>
The format of COMMAND line sent from HS to AG is COMMAND<cr>
The format of RESPONSE line sent from AG to HS is <cr><lf>RESPONSE<cr><lf>
Split rfcomm_write into rfcomm_write_command and rfcomm_write_response to handle
line formatting correctly.
Part-of: <https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/merge_requests/520>
