Due to a misconfiguration on my side my hdmi card didn't load with
snd-hda-codec-hdmi but through the fallback mechanism. Pulseaudio
would crash during early because hctl_handle was null, so skip
init_eld_ctls when hctl_handle is null to prevent a crash.
Thanks to David Henningsson for helping me find the underlying issue.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
If there is a proper monitor name, we expose this as a device.product.name
property on the port. This can be useful for UIs who might want to show
this name.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Generalize the availability flag in order to be used beyond the scope of
ports.
However, pa_port_availability_t is left unchanged to avoid modifying the
protocol and the client API. This should be replaced by pa_available_t
after a validation phase of this new generic enum type.
The previous patch removed module-gconf's dependency on the userdata
pointer of the free callback, and that was the only place where the
userdata pointer of pa_free2_cb_t was used, so now there's no need for
pa_free2_cb_t in pa_hashmap_free(). Using pa_free_cb_t instead allows
removing a significant amount of repetitive code.
In UCM basic functions, we only assign intended roles from modifier
to sink/source, but we don't have a chance to set the ucm modifiers.
Here we amend the functions so that when roled stream starts or
stops, we have the following results:
1. stream will be routed to sink/source specified in modifier by
module-intended-roles
2. After that, modifier will be enabled or disabled.
3. when multiple streams with matched roles of modifier start, only
the first one will enable the modifier, and when they end, the
last one will disable the modifier.
Signed-off-by: Feng Wei <wei.feng@freescale.com>
Signed-off-by: Arun Raghavan <arun.raghavan@collabora.co.uk>
Jack in UCM is decided by UCM device name, although in fact
not all UCM devices have "jacks". Because port is also mapped
to UCM device, we can always find target port when some jack
event happens.
Signed-off-by: Feng Wei <wei.feng@freescale.com>
UCM basic functions will provide another way to handle the alsa mixer
and controls. That means alsa card module will make use of alsa ucm
configurations provided by various audio systems instead of mixer and
paths configurations provided by PA. PA profiles come from UCM verb, PA
sinks/sources and ports come from UCM devices.
In case the proper UCM configurations are found, ucm branches are
activated, or we will still fall through to the original way.
Signed-off-by: Feng Wei <wei.feng@freescale.com>
In practice there is always at least one profile, and I
don't think there will ever be cards without profiles.
Therefore, I added assertions to pa_card_new() stating that
the card new data must always contain at least one profile.
Now a lot of code can be simplified, because it's guaranteed
that the profiles hashmap and the active_profile field are
always non-NULL.
While developing the new UI we had to ask ourselves the question of whether
"speakers" should be considered available when headphones are plugged in.
In most cases, they are not available and therefore we should list them
as such.
OTOH, we don't want unplugging the headphones to be considered an act of
wanting to use the speakers (the user might prefer HDMI), and there might
be line-outs that keeps the speakers from unmuting anyway. So, at this point,
I think the most reasonable would be to make the speakers have
PA_PORT_AVAILABLE_NO when headphones are plugged in and
PA_PORT_AVAILABLE_UNKNOWN when they are not. But we might want to revisit
this decision once we have the priority lists up and running.
The same reasoning applies for "Internal Mic", which should become unavailable
when any other mic is plugged in.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Support the new jack detection interface implemented in Linux 3.3
(and Ubuntu's 3.2 kernel).
Jacks are probed and detected using the snd_hctl_* commands, which
means we need to listen to them using fdlists. As this detection
needs to be active even if there is currently no sink for the jack,
so this polling is done on the card level.
Also add configuration support in paths, like this:
[Jack Headphone]
required-any = any
...where 'Jack Headphone' should match 'Headphone Jack' as given by
ALSA (as seen in e g 'amixer controls').
"Required", "required-any" and "required-absent" is supported. Using
required-any, one can have several ports even though there is no
other indication in the mixer that this path exists.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
To be able to add ports to all profiles, we need to probe all
profiles at startup. To speed this up, we now have a cache of
probes paths which is owned by the profile set. Since paths
are now owned by the profile set, the path set must now have
a hashmap of paths instead of a linked list.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
The new module argument can be used to provide a custom
directory for loading alsa path configuration files. This is
useful for testing: no need to be root to create test
configuration files.
This just covers Lennart's concern over the terminology used.
The majority of this change is simply the following command:
grep -rli sync[-_]volume . | xargs sed -i 's/sync_volume/deferred_volume/g;s/PA_SINK_SYNC_VOLUME/PA_SINK_DEFERRED_VOLUME/g;s/PA_SOURCE_SYNC_VOLUME/PA_SOURCE_DEFERRED_VOLUME/g;s/sync-volume/deferred-volume/g'
Some minor tweaks were added on top to tidy up formatting and
a couple of phrases were clarified too.
This is added so that module-udev-detect can load multiple module-alsa-card
instances with the same card name - forcing namereg_fail to false allows the
name registry to mangle the card names to be unique.
Completely rework mixer logic. This now allows controlling a full set of
elements from a single sink's volume slider/mute button.
This also introduces sink and source "ports" that can be used to choose
different input or output ports with the UI. (i.e. "mic"/"line-in" or
"speaker"/"headphones".
The mixer paths and device maps are now configered in external
configuration files and can be tweaked as necessary.
