If we expose this information, UIs can use this to make better
decisions about what icon to display.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Added Dell Inspiron 3420, 3520 and Vostro 2420, 2520.
Note that this is only necessary for kernels 3.3 to 3.5, as 3.6
has phantom jack support.
BugLink: https://bugs.launchpad.net/bugs/1076840
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
...over "Digital Input Source:Analog Input". It makes life a little
easier for users of Dell xps m1330.
Just an old Ubuntu delta I never upstreamed until now.
The patch was originally written by Daniel T Chen <crimsun@ubuntu.com>.
BugLink: https://bugs.launchpad.net/bugs/453966
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Based on feedback in the bug below (comments 128, 129, 131).
BugLink: https://bugs.launchpad.net/bugs/946232
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
The IDT/Sigmatel codec driver often creates a "Mic Jack Mode" for
every mic jack, so it can change functionality between Mic and Line In.
However, as the "Mic Jack" is the standard naming, our current solution
does not make the Line In port unavailable when nothing is plugged in.
This patch makes the "Line In" port not to be created just because there
is a "Mic Jack Mode" that could be set to "Line". This makes the behaviour
consistent with e g "Dock Mic Jack Mode", "Front Mic Jack Mode" etc, where
we don't create a "Dock Line" or "Dock Mic" port either.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Upstreamed from Debian: "Although in principle Ac '97 hardware has a
separate mono LFE pin nothing seems to use it. To make matters worse
it does confuse PulseAudio's port selection slightly which causes
audio in virtualbox not to work out of the box."
Credit: Sjoerd Simons <sjoerd@debian.org>
Credit: Martin-Éric Racine <martin-eric.racine@iki.fi>
BugLink: https://bugs.launchpad.net/bugs/1016969
BugLink: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=673847
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Some ASUS netbooks, such as the 1015 CX, have only one 3.5 mm jack,
but it can be used either as a headphone or as a mic (but not both
simultaneously).
This patch adds support for the "Headphone Mic" path that is used
on these devices, so that we can use the jack as an external mic, and
doing so without muting the speaker.
BugLink: https://bugs.launchpad.net/bugs/1018262
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
I forgot half of the front headphone patch, i e, to hide the
speaker output when the front headphone is connected. Thanks to
Shih-Yuan Lee for noticing.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Many desktops have headphone on the front and line outs on the back.
Sometimes this means that the headphone is labelled "Front Headphone Jack",
but the volume controls are only "Headphone Playback Volume", i e,
without the "Front" prefix.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Some devices have inverted right channel, so when you add left and right,
the result is silence, or very faint sound. In recent kernels (3.5,
perhaps also 3.4) these are starting to be marked with a special
"Inverted Internal Mic" capture switch.
While we might want to add some reverse summing mechanism in the
future, for now, we just turn the thing off to avoid the problem of
recording silence.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
For kernel 3.6, "phantom jack" kctls have been added. They serve as
a marker that a particular port exist. They were made so we can detect
that there actually are speakers and internal mic on a laptop, even if
there are no other indications (volume controls etc).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Several laptops have speaker ports, and/or internal mic ports, but we have
no way of detecting that. So we make the port(s) always show up for these
devices.
BugLink: https://bugs.launchpad.net/bugs/946232
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Changes in v2:
- Call the mapping a generic 4-channel input mapping
instead of a 4-channel mic array mapping. The mapping
will be used also by sound cards that have two stereo
input jacks, so in those cases talking about mic arrays
is wrong.
- Added a comment about using the "hw" device name.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=45813
Some older cards do not have jack detection. This patch makes the
port still show up.
An implementation detail: the "required = ignore" line has in itself
no effect, but we have to write *something* there, or else the entire
jack detection section will be ignored by the parser.
BugLink: https://bugs.launchpad.net/bugs/961286
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
While developing the new UI we had to ask ourselves the question of whether
"speakers" should be considered available when headphones are plugged in.
In most cases, they are not available and therefore we should list them
as such.
OTOH, we don't want unplugging the headphones to be considered an act of
wanting to use the speakers (the user might prefer HDMI), and there might
be line-outs that keeps the speakers from unmuting anyway. So, at this point,
I think the most reasonable would be to make the speakers have
PA_PORT_AVAILABLE_NO when headphones are plugged in and
PA_PORT_AVAILABLE_UNKNOWN when they are not. But we might want to revisit
this decision once we have the priority lists up and running.
The same reasoning applies for "Internal Mic", which should become unavailable
when any other mic is plugged in.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
For Nvidia and Intel, support probing of up to four HDMI devices.
Also add port information to all HDMI profiles.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Support the new jack detection interface implemented in Linux 3.3
(and Ubuntu's 3.2 kernel).
Jacks are probed and detected using the snd_hctl_* commands, which
means we need to listen to them using fdlists. As this detection
needs to be active even if there is currently no sink for the jack,
so this polling is done on the card level.
Also add configuration support in paths, like this:
[Jack Headphone]
required-any = any
...where 'Jack Headphone' should match 'Headphone Jack' as given by
ALSA (as seen in e g 'amixer controls').
"Required", "required-any" and "required-absent" is supported. Using
required-any, one can have several ports even though there is no
other indication in the mixer that this path exists.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Hi. Could you please apply the attached trivial patch so that I could drop
the corresponding instructions from dcaenc's README file in the future? It
adds a profile for on-the-fly DTS encoding, similar to the existing AC3
profile.
--
Alexander E. Patrakov
>From 22310a1c28385acc7ce883e020b9eb2e5b0813b7 Mon Sep 17 00:00:00 2001
From: "Alexander E. Patrakov" <patrakov@gmail.com>
Date: Sun, 12 Feb 2012 17:19:48 +0600
Subject: [PATCH] alsa: add DTS profile
This requires dcaenc from http://aepatrakov.narod.ru/dcaenc/
"Front Speaker", "Surround Speaker" seems to be a common enough name
to make it into alsa-utils, so we should probably care about it as
well. In this case, there was a macbook pro whose speakers didn't work
without these controls.
BugLink: http://bugs.launchpad.net/bugs/551441
Reported-by: Jeroen T. Vermeulen <jtv@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
The recent change to turn off the IEC958 element for analog paths
exposed a bug in AC3 profiles. These were inheriting the analog output
path instead of explicitly selecting the iec958 path.
Thanks to David Henningsson for pointing this out.
This is needed for the Creative Audigy CA0106 to work. Also makes sure
that the LED for optical out is shut down in analog modes on MacBooks
(these share a port for analog and digital output).
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=44741
Just like we turn off the "Front Mic" element when we select "Rear Mic",
we should also turn off the "Front Mic Boost" element. And the same for
the other inputs.
Reported-by: Len Owens <len@ovenwerks.net>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
The thinkpad ACPI driver sometimes creates a virtual sound card,
which at best exposes a volume control. Save some startup time, and
unnecessary error messages in the log, by ignoring it.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
The Kinect shows up as a UAC device after the firmware has been loaded,
but in order to be detected by pulseaudio a 4-channels input only
mapping is needed. Provide a new profile for that and set it with a udev
rule.
fdo#39664
I've seen more than one system where the volume control named
"Front" is a part of audio path for headphones. This is somewhat
of a compromise: While we don't merge it into the path, as that
would be regressing machines where "Front" isn't a part of the
audio path, it would still enable sound on these machines.
BugLink: http://bugs.launchpad.net/bugs/804178
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
The priorities should be set in the approximately likeliness that someone
would like to use them. This is hard to guess of course, but this is
a better guess compared to the existing configuration.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
The "Line HP Swap" element needs to be set correctly for some Dove
boards to work correctly. Thanks to Daniel T Chen for the patch.
BugLink: http://bugs.launchpad.net/bugs/451635
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
This switch needs to be off for analog output to work on several
Audigy cards.
Thanks to Daniel T Chen for the patch.
BugLink: http://bugs.launchpad.net/bugs/408370
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Now that subset mixer paths are removed, this workaround is no longer needed.
This effectively reverts 1c38b5d478 but due
to me forgetting to add files and adding a couple extra workarounds after,
it's easier to just do this manually rather than run git-revert.
This is a workaround - these usb headsets have one output volume
control only, labeled "Speaker". This causes the default profile
set to not control the volume at all, which is a bug. Workaround
that by creating a separate profile set.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
This change makes it possible to configure an arbitrary constant volume for a
volume element in the path configuration, which is applied when the path is
selected. Note: this is only useful when the exact hardware and driver are
known beforehand.
This feature is mainly useful in embedded systems that have built-in speakers.
In such situations the full audio path is known beforehand, so it's possible to
know what is the maximum sensible volume, and any higher volume can be
disabled.
The volume limit is set in path configuration files in the [Element] section,
using option "volume-limit". The value is the desired maximum volume step of
the volume element.
Make sure that mic and line (with common names) use the specific
path instead of the analog-input one.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
