The mixer paths are not available in ${builddir} - we need to look in
${srcdir}. This should fix running an in-tree build without make install
as well as alsa-mixer-path-test in make distcheck.
Since the most straightforward way to define PA_SRCDIR was in
Makefile.am, I'm moving PA_BUILDDIR there as well for consistency.
On some machines which has a headset jack, the headset mic does not have its own
jack detection. Then we can look at the headphone jack to get some indication:
We know that if the headphone is unplugged, so is the headset mic. The opposite
is not guaranteed since the user might have plugged in a headphone, not a headset.
Also, there exist multi-function jacks which support both Headphone, Mic in headphone jack
and Headset Mic. In this case the jack name will be "Headphone Mic", not "Headphone", so
we need to include this name too.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Found on Logitech B530 USB Headset / kernel 3.8. Because we don't
have different path for headset and headphone today, just add
Headset to the existing headphone path.
BugLink: https://bugs.launchpad.net/bugs/1159687
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Due to a misconfiguration on my side my hdmi card didn't load with
snd-hda-codec-hdmi but through the fallback mechanism. Pulseaudio
would crash during early because hctl_handle was null, so skip
init_eld_ctls when hctl_handle is null to prevent a crash.
Thanks to David Henningsson for helping me find the underlying issue.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
It's valid for a path to have zero elements, e g if it contains
a single jack only. Earlier, this would cause an assertion failure
in pa_path_condense.
Also convert pa_bool_t to bool.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
It's fairly uncommon, but it happens that jack detection is enabled
for some reason, e g hardware design. In that case, we cannot use
jack detection, but we can still use the hint to pick up that there
is a path.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Previously, a drain request was acknowledged up to two hw buffers
too late, causing unnecessary delays.
This implements a new chain of events called process_underrun
which triggers exactly when the sink input has finished playing,
so the drain can be acknowledged quicker.
It could later be improved to give better underrun reporting to
clients too.
Tested-by: Dmitri Paduchikh <dpaduchikh@gmail.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
If there is a proper monitor name, we expose this as a device.product.name
property on the port. This can be useful for UIs who might want to show
this name.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
The alsa mixer kcontrol has "device index" 3, 7, 8, and 9.
We need to configure this properly.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Currently, this function only reads the monitor name, but could
be extended to read e g supported formats as well.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Generalize the availability flag in order to be used beyond the scope of
ports.
However, pa_port_availability_t is left unchanged to avoid modifying the
protocol and the client API. This should be replaced by pa_available_t
after a validation phase of this new generic enum type.
The previous patch removed module-gconf's dependency on the userdata
pointer of the free callback, and that was the only place where the
userdata pointer of pa_free2_cb_t was used, so now there's no need for
pa_free2_cb_t in pa_hashmap_free(). Using pa_free_cb_t instead allows
removing a significant amount of repetitive code.
If 'PlaybackChannels' and 'CaptureChannels' are absent in the UCM
file for a device, assume the device is stereo duplex.
Reported-by: Luke Yelavich <luke.yelavich@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Now you can actually see *which* sink/source that sends a specific
message to the log, which is quite useful if you have more than
one sound card.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
I was looking at a log that showed that a suspend happened (at
a strange time), but the log didn't tell me why the suspend was done.
This patch tries to make sure that that won't happen again.
A left over "required-any" made this path useless for most people.
While we're at it, also add "Front Headphone" like for the normal
speaker path.
Tested-by: Colin Guthrie <gmane@colin.guthr.ie>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
If we expose this information, UIs can use this to make better
decisions about what icon to display.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Added Dell Inspiron 3420, 3520 and Vostro 2420, 2520.
Note that this is only necessary for kernels 3.3 to 3.5, as 3.6
has phantom jack support.
BugLink: https://bugs.launchpad.net/bugs/1076840
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
We inadvertantly stopped supporting non-standard rates when the
passthrough work was done. This makes sure that if no standard rates are
supported, we try to fallback to whatever ALSA gives us.
When a rewind is requested on a sink input, the request parameters are
stored in the pa_sink_input struct. The parameters are reset during
rewind processing, and if the sink decides to ignore the rewind
request due to being suspended, stale parameters are left in
pa_sink_input. It's particularly problematic if the rewrite_bytes
parameter is left at -1, because that will prevent all future rewind
processing on that sink input. So, in order to avoid stale parameters,
every rewind request needs to be processed, even if the sink is
suspended.
Reported-by: Uoti Urpala
...over "Digital Input Source:Analog Input". It makes life a little
easier for users of Dell xps m1330.
Just an old Ubuntu delta I never upstreamed until now.
The patch was originally written by Daniel T Chen <crimsun@ubuntu.com>.
BugLink: https://bugs.launchpad.net/bugs/453966
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Based on feedback in the bug below (comments 128, 129, 131).
BugLink: https://bugs.launchpad.net/bugs/946232
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Refactor code to fetch avail, delay and timestamp values
in a single call to snd_pcm_status().
The information reported is exactly the same as before,
however it is extracted in a more atomic manner to
improve timer-based scheduling.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
The IDT/Sigmatel codec driver often creates a "Mic Jack Mode" for
every mic jack, so it can change functionality between Mic and Line In.
However, as the "Mic Jack" is the standard naming, our current solution
does not make the Line In port unavailable when nothing is plugged in.
This patch makes the "Line In" port not to be created just because there
is a "Mic Jack Mode" that could be set to "Line". This makes the behaviour
consistent with e g "Dock Mic Jack Mode", "Front Mic Jack Mode" etc, where
we don't create a "Dock Line" or "Dock Mic" port either.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Sometimes the kernel does not schedule us in due time, thus causing
an underrun. Adding a detection and a debug message will be a helpful
step in determining the cause of an underrun.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Upstreamed from Debian: "Although in principle Ac '97 hardware has a
separate mono LFE pin nothing seems to use it. To make matters worse
it does confuse PulseAudio's port selection slightly which causes
audio in virtualbox not to work out of the box."
Credit: Sjoerd Simons <sjoerd@debian.org>
Credit: Martin-Éric Racine <martin-eric.racine@iki.fi>
BugLink: https://bugs.launchpad.net/bugs/1016969
BugLink: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=673847
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
I was hoping this would improve bootup speed, but it doesn't seem
to do so here, at least not much. But at least it reduces the logs
a little.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Interestingly, the name is properly matched even though there
is no paths/iec958-stereo-input.conf file.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
In UCM basic functions, we only assign intended roles from modifier
to sink/source, but we don't have a chance to set the ucm modifiers.
Here we amend the functions so that when roled stream starts or
stops, we have the following results:
1. stream will be routed to sink/source specified in modifier by
module-intended-roles
2. After that, modifier will be enabled or disabled.
3. when multiple streams with matched roles of modifier start, only
the first one will enable the modifier, and when they end, the
last one will disable the modifier.
Signed-off-by: Feng Wei <wei.feng@freescale.com>
Signed-off-by: Arun Raghavan <arun.raghavan@collabora.co.uk>
Modifiers may have their own PlaybackPCM/CapturePCM and for these, we
create separate sinks/sources. These are marked with the
device.intended_roles property to let role-based routing take care if
streams are tagged appropriately.
The proplist isn't used by the conventional alsa-mixer code path, but
can be used by UCM to transfer properties from UCM data to the
sinks/sources corresponding to a mapping. These properties could be used
later in policy, etc.
The specific use for which I'm writing this now is for UCM modifiers
that have their own PlaybackPCM/CapturePCM field. These will be
translated to a separate sink/source corresponding to the modifier by
adding an additional mapping per sink/source. These mappings' proplist
will be populated with the name of the modifier and corresponding
"device.intended_role" property. The latter will be used in the usual
routing-by-role way, and the former will be used during sink/source
activation and deactivation to know what UCM modifier is to be enabled
or disabled.
Jack in UCM is decided by UCM device name, although in fact
not all UCM devices have "jacks". Because port is also mapped
to UCM device, we can always find target port when some jack
event happens.
Signed-off-by: Feng Wei <wei.feng@freescale.com>
UCM basic functions will provide another way to handle the alsa mixer
and controls. That means alsa card module will make use of alsa ucm
configurations provided by various audio systems instead of mixer and
paths configurations provided by PA. PA profiles come from UCM verb, PA
sinks/sources and ports come from UCM devices.
In case the proper UCM configurations are found, ucm branches are
activated, or we will still fall through to the original way.
Signed-off-by: Feng Wei <wei.feng@freescale.com>
Some ASUS netbooks, such as the 1015 CX, have only one 3.5 mm jack,
but it can be used either as a headphone or as a mic (but not both
simultaneously).
This patch adds support for the "Headphone Mic" path that is used
on these devices, so that we can use the jack as an external mic, and
doing so without muting the speaker.
BugLink: https://bugs.launchpad.net/bugs/1018262
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
As these functions are called together and are related, we might merge
them and call setting_select from pa_alsa_path_select by passing
optional pa_alsa_setting argument.
Make also the setting_select static as it is not called outside of
alsa-mixer.c after this change.
[Additional note from Tanu Kaskinen: this change improves the
mute-during-activation feature, because now the mixer changes related
to selecting the setting happen while the hw is muted.]
Move pa_alsa_setting_select call just after the pa_alsa_path_select in
[sink | source]_set_port_cb functions as there is no dependency to volume
calculations that are done between these two calls. Idea here is to make
possible to merge these two functions since they are called together from
other places too.
I forgot half of the front headphone patch, i e, to hide the
speaker output when the front headphone is connected. Thanks to
Shih-Yuan Lee for noticing.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Many desktops have headphone on the front and line outs on the back.
Sometimes this means that the headphone is labelled "Front Headphone Jack",
but the volume controls are only "Headphone Playback Volume", i e,
without the "Front" prefix.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
