Convert capture and playback streams to any global channel position that
has been set. This can then be used to implement an upmix sink and add
such an example config.
When we don't set a rate, assume both input and output streams are
following the graph rate and so disable the resampler.
This mostly works around an issue where the input and output could
negotiate to different rates in some cases. With the resampler disabled
this would still result in the same amount of samples going in as
comming out instead of a stuttering mismatch.
See #2969
When one side of the loopback suspends, do a EnumFormat params to force
renegotiation on the other side as well.
Suppose this:
1. sink/filter/pw-play plays at 48000Hz
2. pw-play goes away, sink and filter-sink suspend, filter-playback
idles
3. pw-play starts with 44100Hz
4. sink/filter-sink renegotiate to 44100Hz, filter-playback is still
at 48000Hz and pitch shifted.
We might want to manually suspend the IDLE nodes instead but for now
this is a good workaround.
Fixes#2969
Because the capture triggers the playback stream, the playback stream
might not be actually triggered when the stream is not running.
This can cause a buffer to be queued in the capture side that is never
dequeued from the playback side. If 2 buffers are queued (and 2 buffers
are available on the stream), the capture source has no more buffers and
starts to drop/stutter.
Fix this problem by always dequeueing/queuing all the queued buffers so
that we always use the last one.
See #3276
When one side of the loopback suspends, do a EnumFormat params to force
renegotiation on the other side as well.
Suppose this:
1. sink/filter/pw-play plays at 48000Hz
2. pw-play goes away, sink and filter-sink suspend, filter-playback
idles
3. pw-play starts with 44100Hz
4. sink/filter-sink renegotiate to 44100Hz, filter-playback is still
at 48000Hz and pitch shifted.
We might want to manually suspend the IDLE nodes instead but for now
this is a good workaround.
Fixes#2969
Connect the playback stream before the capture stream since the capture
stream can otherwise trigger playback_process() before the playback node
has been activated.
Modules echo-cancel, filter-chain and loopback may print errors if no
applicable target nodes exist when they start up. For our products this
is not considered error/warning worthy, since the issue will resolve
itself once the target nodes exist.
Add a target.delay.sec property to module-loopback that uses a
ringbuffer to further delay the signal to the requested value. This
also takes into account the graph delay to get an end-to-end delay.
Add a -d property to pw-loopback to control this.
Implement latency_msec on the pulse module with this new property so
that it behaves similar to pulseaudio.
First go over all the input and collect pointers and the size that we
need to copy. Then go over all destinations and copy the source or
clear the buffer memory.
This fixes the problem where extra planes in the destination would get
a 0 size, which would make the converter produce 0 output. It also
ensure that the output size is consistent.
It's possible that the stream is sent an error when the session manager
can't link the node (because, for example, the sink/source is not
available yet). We should not stop but just log this error.
When the session manager actively kills the stream (when it is
reconnected while the DONT_RECONNECT flag is true) we will end up in the
UNCONNECTED state and that's when we can unload the module.
Make sure the node name is something unique for the capture and playback
part of filter-chain and loopback so that volumes can be remembered
separately.
Fixes#1983
If not otherwise set, the media.name will be the name used when
pw_stream_new(), which is the same for all loopback streams.
This makes the session manager restore the same volume for all
loopback streams.
Do something more clever and use the node.name + suffix to make
the name unique per stream if no media.name was given.
Fixes#1942
The trigger flag adds an extra dependency on the node so that it does
not automatically get scheduled. A manual scheduling is required with,
for example pw_stream_trigger_process().
This can be used to create an artificial dependency between a sink
stream and a source stream, like when using loopback or filter-chain.
Normally those streams are not linked in the graph but they have an
internal dependency. Without any such dependency, the source part of the
chain will be scheduled first and then the sink part and we get a
cycle of delay (with possible quantum change etc).
With this patch, the sink part will be scheduled first and its process
function will trigger the 'downstream' source stream explicitly. The
sink and source stream will stay in sync and will use the same quantum.
This reduces the latency and glitches because of quantum changes.
Fixes#1873
