Auto-connect all paired & trusted devices on startup.
Since devices that already connected or powering off would reject the connecting requests, it should be fine with this behavior.
Also reconnect remaining profiles if only partial profiles are connected.
So that we can know if this node has routes or not.
Nodes without routes might need their volumes restored directly
with the node properties, like streams. Nodes with a route need their
volumes set on the device managing the node.
Implement switching HFP codecs in bluez5-devices, currently only for
backend-native.
Codecs are exposed via profiles similarly as for A2DP.
Some hardware appears to not properly reply to the +BCS message. Catch
these cases with a timeout, in which case we fall back to previously
existing transports.
This profile is meant to be used with audio gateways, such as mobile
phones, making pipewire act as a headset. It activates all 3 "dynamic"
nodes (all of which are "Stream/*/Audio"), allowing both A2DP source
and HSP/HFP AG to be available at the same time. Ultimately, the remote
device (the AG), is the one that decides which profile to use and pipewire
just creates/destroys the appropriate stream nodes dynamically.
To make things less confusing, the HFP/HSP profile is now only available
if the remote device is a Head Unit and the A2DP profile is only available
if the remote device has an A2DP Sink.
If the device has both A2DP Source & A2DP Sink (not sure if this is a real world
possibility, but just in case...), the A2DP profile allows using them both,
while the AG profile will only allow the source.
In addition, to keep things less complex, the routes are now only used for
device nodes (the "Audio/*" ones). A2DP source and HSP/HFP AG never have a route.
Restoring their props should be possible to be handled by the restore-stream
module.
errno should be set to the positive errno value.
This does not cause problems except for the pulse-server where the
errno value is negated and returned as an error result.
Typically a source stops the connection when it has nothing to play
and this causes the transport to become "idle" and our A2DP source
also stops. However, the node is still present and "running" (if linked),
which causes the graph to underrun as it receives no data from this node.
This patch dynamically creates and destroys the a2dp source node depending
on the transport state. So, when the transport is idle, there is no node
in the graph at all.
SCO transports have timer-delayed release, but they need to be released
immediately when changing profiles to close connections before switching
to A2DP.
Mark bluez5 routes always available in EnumRoute, because there's always
a device connected.
Fixes default-route resetting profiles back, when they are manually
changed.
This does not work as intended, because we no longer do a codec switch
on device connect. It should be done in a different way, but since it's
not used for anything right now, can as well remove it.
This may avoid infinite loops if parameters are being set based on events
sent by parameter changes. It's also what alsa-acp devices do, so bluez5
should follow.
Not all devices report their A2DP delay. In those cases, use a fallback
value of 150ms by default.
Make the delay adjustable with a SPA_Prop, and expose it as a part of
the route. Implement the corresponding parts in media-session.
Set initial device profile according to what's connected at startup,
rather than having media-session try to set it to A2DP (and fail, if the
profile was not connected, resulting to startup in null profile).
This avoids making a codec switch at device startup (we'll stay with
what BlueZ autoconnected us to, usually the previously used codec).
default-route wants to have SPA_PARAM_ROUTE_devices and
card.profile.devices before it will restore routes. Add these
also for bluez5-devices.
Fixes restoring volumes on Bluetooth profile change.
BlueZ may connect transports long after DEVICE_PROFILE_TRANSPORT_SEC has
passed on already existing devices. When this occurs, the bluez5
pipewire device should notify that the profile enumeration has changed.
Ignore these events during A2DP codec switch, and handle any changes
when the switch completes.
Set form factor, name routes based on form factor.
Improve profile names
Make card and node names like pulseaudio, with bt address in them.
Fill in port type in the route info.
Fixes#544
Implement routes on the device. This makes it possible for the
session manager to restore the device volumes.
Use validate_config to get the negotiated channels for the route
volumes.
Use the same code to enumerate the profiles and the current profile,
this makes sure we have all info in the Profile param as well and
don't need to do a lookup in the EnumProfile.
