Use the quirks database to check whether to enable MSBC codec for each
device.
If quirks don't allow ALT1 mode for an USB adapter, check whether the
adapter has an usable ALT6 mode and disable MSBC if not.
It seems few devices support the Device Id via bluez.
Try to figure out vendor/product ids for usb devices also via sysfs.
Also try to figure out the adapter bus type.
Keep all types of devices, only emit device info if device has audio profiles.
Heuristically add profiles based on bluez actions so device can still be connected
even without initial UUIDs info from signal InterfaceAdded for org.bluez.Device1.
Fixes#1330
Always set the HAVE_OUTPUT flag because we always consume the
input and produce output, either to a buffer or an error.
This makes sure processing never stalls when something is wrong
on the output side.
See #1305
Follow the rate of the _io_position area and adjust the resampler
to match. This ensures that we always process at the DSP samplerate
to the target negotiated fixed rate of the device/stream.
The merger and splitter use the samplerate from the _io_position
for the DSP formats so set the samplerate to 0 to make sure we
don't use it to negotiate a format with the peer.
Move the code to check the position duration for changes to one
new method.
Also check for samplerate changes and adjust the resampler state
accordingly.
impl_add_listener() could be called more than one time, ensure that we always emit node info
so that session manager(bluez-monitor) can receives it.
Fixes#1308
Strip the _alibpref from the device name, it contains a local counter
to identify the ucm card that should remain internal. We set a flag on
the device to notify of this.
Re-add the _alibpref of the local card to the device name if the
device was flagged.
See #1286
The _alibpref of the device was created in the session manager and
does not match our local _alibpref. Patch the device name with
the local _alibpref to make things match.
See #1286
The alibpref fallback does not contain the card number but it is
a local counter instead. Just check if it starts with something in
case the alsa library is not patched to return _alibpref.
These headers are designed for including in the project. So the user doesn't
need to install valgrind-devel and we don't have to worry about whether the
headers are available or not.
Set this once during setup so we don't have to remember to call fflush() after
each logging operation.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
In the interested of making the logs narrower, let's drop some digits from the
clock_gettime() seconds value. Clamping to 5 digigts, this gives us just under
28h before we wrap which is likely good enough for debugging.
Write the timestamp and location into a temporary buffer, then include them in
the message print. This makes bugs involving size vs length less likely and
provides a fixed limit for how much space the filename can take in the
message.
The two are functionally equivalent, but spa_snprintf never returns a value
higher than the size, preventing memory corruption where our input string
exceeds the target buffer size (see c851349f1).
Niche case: we can no longer differ between real overflow and fitting an
N-byte string into an N+1 sized buffer, we now get a "...truncated" message
now for log messages of exactly 999 bytes long.
bluez5 nodes will always be removed & created again during profile changing, hence
node volume & mute will always be reset. This is OK if profile did changed, because
session manager would carries volume & mute to bluez5 route param. But if profile
was not changed after setting profile (a2dp-sink-sbc -> a2dp-sink -> a2dp-sink-sbc),
session manager would think node volume & mute are not changed and no route
setting is performed, causing route volume out of sync with node volume.
To fix this, we emit node volume and mute right after bluez5 node is created.
Fixes#1254
Use _alibpref to check if a device needs a UCM local config. Mark
the device as such and use this to set the OPEN_UCM property on
the device.
Open the UCM for a card when the device has the property set. Use the
same logic for loading the UCM as the acp code.
See #1251
UCM devices can require local data from use_case_mgr_open() but since
we do that in a separate process, make sure we reopen the use case
manager in case we are passed a UCM device so that the config is
available.
See #1251
When we enable a device, the node will be created and its software
volume will be set to 100%. Update the device volume with this as
well so that changing the volume has an effect.
Fixes#1198
According to the alsa-info.txt in the pipewire issues of #747 and #1206,
the Front Playback Volume is shared by Headphone and Lineout or
Headphone and Speaker, But Headphone, Lineout or Speaker they all have
independent Playback Switch, change to only use switch to mute the
Lineout or Speaker. This could resolve the issues of #747 and #1206.
See #1206 and #747
