When acting as SCO AG / A2DP sink, the remote end should decide when to
close the connection. This does not work currently properly, because
stopping sources/sinks releases the transport, which causes it to go
idle, and which then destroys dynamic nodes. The sources/sinks should
not cause the transport to be released.
Implement keepalive flag for spa_bt_transport, such that
spa_bt_transport_release does not actually release the transport when
the refcount reaches zero. Set the flag for dynamic nodes when the
transport becomes pending (remote end connects) and unset the flag when
idle (remote end disconnected, or dynamic node removed).
Using a probe connection to determine adapter msbc capability causes
problems on some adapters (ff8c3d2, 84bc0490a5, 717004334b,
pipewire#2030) and seems to be a bad idea.
Go back to probing for transparent msbc transport capability via HCI
commands. bluetooth/hci.h may be deprecated later, but for now it's
better to go back to using it. (In practice, adapters not supporting
esco appear to be fairly rare; kernel commit in 2013 refers to "older
devices", so if we can't use HCI, assume the adapter supports the
necessary modes.)
A2DP profile may disappear if several SetConfiguration events occur too
rapidly. Rate limit these calls when switching codecs.
This resolves failures if e.g. the session manager attempts to set the
profile immediately after the device is created, which previously might
cause a failure.
Some devices (Bose Mini Soundlink II, Air 1 Plus, ...) don't enable
AVRCP volume control, or fail to enable it before a hardware button is
pressed. However, these devices appear to enable it, if an AVRCP player
is present.
As a workaround, register a dummy AVRCP player for each adapter. It only
displays the current transport acquisition state as playing/stopped, but
just its presence appears to be enough to make devices behave.
Multiple AVRCP players interfere with each other, as BlueZ uses the one
registered earliest as the default player. So add also a config option
for disabling this. (It's not common to have mpris-proxy etc. running,
so defaulting to true should be OK.)
See pipewire#1157
It seems not uncommon that people have not properly configured ofono
running, which results to loss of HFP/HSP functionality. It's less
surprising if the backend selection is fixed in the configuration file,
and (by default) does not depend on running services.
Add a configuration file option for selecting HFP/HSP backend, and set
the default value to the native backend. Emit warnings if conflicting
backend services are detected to be running.
Also cleanup hfp/hsp backend handling a bit, now that it's mostly
abstracted behind an interface.
aptX-LL sink devices may send back mSBC encoded data corresponding to
microphone input. It appears to be enabled when the bidirectional link
is set in the caps, and the device also supports this.
Implement mSBC decoding in the duplex channel.
Tested to be working on Avantree Aria Pro.
HF indicator 2 (see [assigned-numbers], Hands-Free Profile) is able to
report battery percentage at 1% intervals (in range [0, 100]), contrary
to the `+XAPL` `+IPHONEACCEV` extension which only supports 10%
increments. This does not guarantee increased granularity however, as
peers may still be limited to imprecise battery measurements internally
or round to coarser percentages.
Supporting both additionally broadens the range of devices for which PW
can report its battery level.
[assigned-numbers]:
https://www.bluetooth.com/specifications/assigned-numbers/
Mark some structures, arrays static/const at various places.
In some cases this prevents unnecessary initialization
when a function is entered.
All in all, the text segments across all shared
libraries are reduced by about 2 KiB. However,
the total size increases by about 2 KiB as well.
It seems few devices support the Device Id via bluez.
Try to figure out vendor/product ids for usb devices also via sysfs.
Also try to figure out the adapter bus type.
Keep all types of devices, only emit device info if device has audio profiles.
Heuristically add profiles based on bluez actions so device can still be connected
even without initial UUIDs info from signal InterfaceAdded for org.bluez.Device1.
Fixes#1330
Add necessary apis to bluez transport.
Add A2DP(AVRCP) absolute volume support. Source volume can only update to adapter node but not from due to AG nodes don't have route.
Since A2DP/HSP/HFP volume is already percentage itself, it has been mapped to pulseaudio volume then converting to linear volume.
There won't be further battery level updates when RFCOMM connection is
down, so remove the battery then.
Fix minor things with canceling the provider registration.
Auto-connect all paired & trusted devices on startup.
Since devices that already connected or powering off would reject the connecting requests, it should be fine with this behavior.
Also reconnect remaining profiles if only partial profiles are connected.
Implement switching HFP codecs in bluez5-devices, currently only for
backend-native.
Codecs are exposed via profiles similarly as for A2DP.
Some hardware appears to not properly reply to the +BCS message. Catch
these cases with a timeout, in which case we fall back to previously
existing transports.
SCO transports have timer-delayed release, but they need to be released
immediately when changing profiles to close connections before switching
to A2DP.
This does not work as intended, because we no longer do a codec switch
on device connect. It should be done in a different way, but since it's
not used for anything right now, can as well remove it.
This will prevent to run the different backends concurrently.
The native backend will only register to BlueZ if neither oFono nor
hsphfpd are running. If one of them starts, the native backend will be
unregistered and the corresponding backend will register to its daemon.
Make queueing a codec switch work properly. When receiving the dbus
reply, it should move to latest one. Others should be discarded.
Previously, it instead hit an assert, if there were more than two
queued.
Not all devices report their A2DP delay. In those cases, use a fallback
value of 150ms by default.
Make the delay adjustable with a SPA_Prop, and expose it as a part of
the route. Implement the corresponding parts in media-session.
BlueZ may connect transports long after DEVICE_PROFILE_TRANSPORT_SEC has
passed on already existing devices. When this occurs, the bluez5
pipewire device should notify that the profile enumeration has changed.
Ignore these events during A2DP codec switch, and handle any changes
when the switch completes.
