The volume synchronization could be done even if there's no audio link
and so no transport opened.
This patch allows to send the Speaker (AT+VGS) and Microphone (AT+VGM)
commands at the end of the SLC. And to exchange volume updates using the
telephony DBus interface, even without a transport.
HFP/HF/TWC/BV-03-C test, which setup an active and a held calls,
expects to receive AT+CHLD=1 (release and swap calls) instead of
AT+CHUP on active call hang up request.
As this changes the active call to disconnected and held call to
being active, the call states should be managed in hfp_hf_hangup
instead of waiting for +CIEV (callheld=0) event which will drop
the previously held call before AT+CLCC reply can inform this call
is now active.
HFP/HF/TWC/BV-01-C test creates an incoming call as soon as the SLC is
completed, i.e. a +CIEV: <callsetup>,1 event just after AT+CHLD=? reply
has been received. This try to parse the rfcomm->telephony_ag->call_list
which has not yet been created.
This commit move the telephony_ag creation to the SLC completed event.
In this error condition, execution is supposed to return immediately
because rfcomm is no longer valid. However, the code was incorrectly
changed to jump to the done label, which would try to use rfcomm
again to process pending commands.
To be sure that the AG reply correspond to the command sent, this
postpone the new command if previous reply (OK, ERROR or +CME) has
not yet been received.
The postponed command is sent on reception of the reply.
This allows implementing UI mechanisms to transfer the audio of a call
to the HF (pipewire) only when the user explicitly asks/allows it.
Normally, when a call is connected, the phone initiates a SCO connection
and the HF accepts it, transfering audio automatically. In order to
allow for user interaction, this patch enables the UI to set the RejectSCO
property to 'true' in order to automatically reject the SCO connection.
Later on, at the UI's discression, the audio may be reconnected by calling
the Activate() method, which sends AT+BCC to re-initialize the SCO channel.
A configuration file option is also added to configure the default value
of the RejectSCO property. By setting this to 'true' in the config file,
it is possible to implement rejecting the audio of a call that is already
active at the time the Bluetooth connection to the phone initializes.
This is useful for implementations that do hardware offloading of the
SCO audio channel and need to communicate state information to the
hardware (at least).
Start call id at 1 as for the index calls in HFP, and move this id
to spa_bt_telephony_[ag|call] so they can be used by CLCC to retrieve
the related call.
if enhanced call status is supported, send AT+CLCC on +CIEV events to
get the calls information.
The HF should declare the features supported before trying to send
related AT commands.
It should only send AT+CHLD related commands if the remote AG supports
them.
On some phones (at least), sending AT+CHLD=0 while there is no held
call returns an error. Make sure we don't do this to avoid returning
an error on D-Bus when in fact hangup_all actually succeeds.
This commit implements the dial, answer and hangup callbacks to manage
call when connected to HFP AG device.
This adds +CLIP support to be able to get remote party phone number.
Claim that call waiting notifications are supported.
Required for some devices (e.g. Soundcore Motion 300),
as they stop sending commands if the reply to CCWA is not OK.
Kernel-provided MTU does not work for USB controllers and the correct
packet size to send can be known currently only from RX. So we are
waiting for RX to get it.
The known problem is USB-specific, we shouldn't need the workaround for
other transport types.
Don't wait for POLLIN for non-USB controllers on connect, but ready
things on POLLOUT as usual.
For non-USB controllers, pick some sensible packet sizes to use
initially, before we switch to same size as for RX.
The file is moved into a new "include-private" directory. This is done
because otherwise adjustments would have to be made to the list of installed
headers, the way include tests currently work and which files are
used for generating documentation.
The rfcomm list may contain various AG & HF ones, so the profile must be
checked everywhere they are looked up.
Fix the rfcomm lookups everywhere to do it.
Fixes Pipewire<->Pipewire HFP connections, and sending HFP HF commands
to HSP or AG.
HFP 1.9 adds LC3 as a possible codec in addition to CVSD & mSBC.
E.g. Pixel Buds Pro latest firmware supports it.
Add the RFCOMM side and codec selection for it.
Do relaxed parsing of RFCOMM commands for AG & HF roles, allowing
multiple commands in same buffer.
Use same parser code for all HFP/HSP AG/HF. Parse input in relaxed way,
as some devices emit spurious \n
Use bigger fallback maximum MTU, when kernel fails to tell us, which
shouldn't happen but apparently can. We choose the packet size based on
incoming data, so these values aren't usually needed so we can just bump
them.
Also report errors as necessary.
It may occur that we have RFCOMM connected as both HF and AG. The codec
switching and support checks should in this case always use the remote
HF RFCOMM.
Fix by finding the RFCOMM with the correct profile, remote as HF.
