Remove the check for the target rate and duration. The drivers are
supposed to update that now.
The check is a little racy because a new target could have been
configured right after the driver emitted the ready signal. In that
case we should not update the clock values but let the driver run with
the old values and let the new values become active in the next cycle.
When the driver starts, save all previous node timestamps, not just the
previous signal time.
For async nodes, uses the previous timestamps in the profiler messages
so that we get stats with 1 cycle of delay instead of bogus values
because the node is still processing.
Fixes pw-top for async nodes.
Add a filter-graph info structure with the number of inputs and outputs
in the graph definition.
Use the input/outputs to update the number of channels on the capture and
playback streams when not explicitly given. Also copy over the positions
when they match the other stream and were not explicitly specified.
Fixes#4404
If the peer announces an interlace mode then use it. Otherwise assume
that the video is not interlaced.
This also fixes a problem with caps negotiation:
If downstream reports caps with not fixated interlace mode, e.g.
"interlace-mode=(string){ progressive, interleaved, mixed }"
then without this, the caps handle_format_change() (in the pipewiresrc)
are not fixed and the source waits forever for the negotiation to
finish.
Always listen on the receive socket. Find the stream with the given
stream_name of the packet and create it if it doesn't exist.
Also take the sample-rate, channels and format from the packet
parameters instead of the config.
Fixes#4400
Make SPA plugins from all the filter-graph plugins and use the plugin
loader to load them.
Because they are not in the standard plugin path in development, add
the module dir to the plugin path for now.
Make a plugin structure that is dynamically allocated for each plugin
and pass it around to the descriptor instance structures, so that they
all have access to dsp_ops without sharing a static pointer.
The problem with the static pointer is that the dsp_ops structure is
actually allocated in module-filter-chain's instance structure,
so it always points to the instance of the last filter-chain that was
loaded in the process. When this is unloaded, the other filter-chains
crash.
The src can listen to RequestProcess commands and so gets the
node.supports-request = 1 property.
The play-pull example can both be a driver that listens to
RequestProcess or a lazy driver so set this in properties as well.
We can now remove the priority.driver property because automatic
priority selection will make us a driver or not.
With this change, video-src to video-play-pull will use lazy scheduling
with play-pull as the driver. video-play-pull to v4l2src will use
normal scheduling and video-src to video-play will also use normal
scheduling.
Collect the request scheduling flags and when there is a lazy driver,
set the lazy scheduling flag in its clock. This means that the driver
can expect RequestProcess commands to start the scheduling.
Pass the lazy scheduling clock flag to the node.
Make sure lazy scheduling driver have a higher priority than their
request drivers.
Take the current cycle times early and in all cases. We can use this to
get the current frame time for debugging purposes instead of the more
heavy jack_frame_time().
Rate limit the xrun warnings.
So that we can have different versions per FFT.
One possible optimization would be to split the complex number in
separate real and imag arrays. This would speed up the multiply
operations.
When we get a process callback from the capture stream but we can't
trigger the playback stream, simply consume the buffers from the capture
stream.
This can happen when the playback stream is not ready yet, for example.
If we don't consume the buffers that are ready, the converter might run
out of buffers and complain.
The current implementation uses the slope variable S to define the
filter slope. Setting S = 1 results in a constant Q value of
sqrt(2)/2, or 0.7071, which is a good default value.
However, calculating alpha from the Q value instead, as done in
RBJ's cookbook [1], the filter shape can be changed which might
be desired for certain applications and provides flexibility.
Since the current implementation always defaulted to using S = 1,
make sure that configurations missing Q uses the same slope value.
[1] = https://www.w3.org/TR/audio-eq-cookbook/
Client-side bugs calling methods on destroyed proxies like
pw_proxy_ref(p);
pw_proxy_destroy(p);
...
wait for server to ack the remove
...
pw_core_destroy(p->core, p); /* p already removed & destroyed */
should not send messages with the stale proxy id to server.
Set id to SPA_ID_INVALID when removing a proxy from the id map, so that
such client bugs only result to ENOENT.
