Let's just directly use the next timer value from the other side
directly, and the reference time as well to calculate the expected next
sample position we want to send from on this side.
For ASHA stereo, the timer for flushing packets on both sides of a
pair should be as closed to each other as possible.
Also set seqnum before first flush so other side sends the correct
packets at the start.
In ASHA, we might need to sync sequence numbers between
left and right side media sink. If the sequence number
is added in start encode, it becomes difficult to set
the sequence number again when a call to reset_buffer
in media sink might have happened already.
This effectively reverts commit ab5f81b9a.
ASHA devices with the same HiSyncId are a pair and this
will be used later on to set them up together with a
combine sink like device set for BAP. Side information
is required for channel information when setting up the
combine sink.
The +BCS event may interrupt any of the initialization commands after
SLC is established and by changing the state here we may lose track
of the initialization sequence.
There is no reason to have the hfp_hf_bcs state anyway. If the
initialization sequence is over, we can remain in the hfp_hf_vgm state.
Some devices have a hardware volume control, but not a dedicated
hardware mute control. In some of these cases, the volume control is
described as having a hardware mute when volume is 0. This is described
in the TLV information of the volume control, when the
SNDRV_CTL_TLVD_DB_SCALE_MUTE flag is set in the TLV structure.
If set, alsa-lib will set the minimum dB value to -99999.99dB, which
can be detected inside PipeWire.
PipeWire can then use this hardware volume control to apply hardware
mute, when set.
In order to be able to set volumes and mutes separately, changing the
volume whilst muted will save the value, but not write it to the
hardware. When the device is unmuted, the saved value will be restored.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Print the error in td->err (the SO_ERROR) or else let the user know
this is a regular hangup. The previous printout was always reporting
EAGAIN (remainder in errno from the event loop code, I suppose)
as an error, without any real data.
Do some of the counting of the nodes and controls when we add a node
to make things easier later.
Do the setup of the graph controls after loading the graph because we
know exactly how many controls we will have.
Fixes controls being unavailable until the filter-graph is activated.
We usualy want to prefer the filter default value. When this value is
not within the valid range/alternatives, swap the logic and prefer the
defaults of the other pod.
This way we can have a filter with an invalid default that will then use
the preference of the other pod but still enforce some bounds.
Build the filtered result into a new separate builder and copy it into
the result builder afterwards. This ensures the memory of the old
builder does not suddenly change when it gets reallocated.
The continue functions takes a builder as the argument and makes a new
builder that starts from the old builder memory. If the old builder was
dynamic, the new one will also be dynamic. Because it's a separate
builder, the memory of the old builder will not be reallocated when
extended.
This makes it possible to freely read the memory from the old builder
while we construct the result in a new builder without having to worry
about reallocating the memory of the old builder. When the new object is
completed, it can then be copied into the old builder.
Use kernel-provided packet reception timestamps to get less jitter in
packet timings. Mostly matters for ISO/SCO which have regular schedule.
A2DP (L2CAP) doesn't currently do RX timestamps in kernel, but we can as
well use the same mechanism for it.
Add configuration options for the BAP/PACS sink and source endpoint
location (= channel positions) and context settings.
Although BlueZ associates these with individual endpoints, in the PACS
spec they are actually device-global, so configure directly in monitor
settings.
Parse BAP settings in a single place, and simplify QoS customization a
bit.
Ensure the selected preset gets selected.
For all the BAP codec settings, use device settings instead of global
monitor ones.
The current BAP QoS configuration allows to register a sampling
frequency based on the configuration done using wireplumber configuration.
However, for a scenario were the user need to use a specific SDU framelength
it cannot be done as the select_bap_qos function selects the QOS based on
priority and hence it will use the best possible config rather than the user
configured.
This PR adds option to select the QoS set based on user configured value. If
the remote device doesn't have the user configured capabilities it will always
use the best priority config.
Further, this change also allows the user to set RTN, Latency, Delay QoS config
for certain use case to have controller use optimum bandwidth usage.
Below are the example configuration on setting LC3 capabilities in config file:
bluez5.bap.set_name = "48_2_1"
bluez5.bap.rtn = 5
bluez5.bap.latency = 20
bluez5.bap.delay = 40000
bluez5.framing = false
The current BAP unicast QoS configuration allows to register a sampling
frequency based on the configuration done using wireplumber configuration.
However, for a scenario were the user need to use a specific SDU framelength
it cannot be done as the select_bap_qos function selects the QoS based on
priority and hence it will use the best possible config rather than the user
configured.
This PR adds option to select the QoS set based on user configured value. If
the remote device doesn't have the user configured capabilities it will always
use the best priority config.
Further, this change also allows the user to set RTN, Latency, Delay QoS config
for certain use case to have controller use optimum bandwidth usage.
Below is the example for the options that can be configured & selected
in config file:
bluez5.bap.set_name = "48_2_1"
bluez5.bap.rtn = 5
bluez5.bap.latency = 20
bluez5.bap.delay = 40000
bluez5.framing = false
Parameter values read into a 512 byte long buffer, which is insufficient
for medium to long filter-graph parameters.
Increase the buffer to 4096 bytes to give some wiggle-room.
Parse and use DSP formats.
Redo the conversion setup when the formats changed. We usually do this
when starting the node but the formats can change while running as well.
